Humongous input lag - Page 2

SolidSnake3035 · 04-06-2008, 08:17 PM

This seriously sucks because I have to raid tonight and I'm screwed because all I can basically do is listen since no one hears anything I say for at LEAST 5 seconds...

I could be dead by the time I get a heal that I ask for, for example...

machz · 04-07-2008, 04:28 AM

This problem started about 5 weeks ago for me as well.

mjgraf · 04-07-2008, 08:35 PM

that tracert is showing some packet loss.

I Would contact the ISP and see if they are performing packet shaping, as this may be incorrectly flagging ventrilo packets as low priority.

SolidSnake3035 · 04-07-2008, 11:31 PM

All it's showing is that one of the routes is unpingable...

My ISP doesn't tell me anything, maybe YOU guys should contact them seeing as how you'd know a lot more about what to tell them than I would. Maybe they'd listen to someone from the company that actually makes the program.

Fayde · 04-08-2008, 09:56 AM

I have the excat same problem. Although, sometimes it works fine for long perdiods of time, and sometimes the lag comes every minute. I can still hear everyone perfectly, with no delay (I usually have 10 ms depending on server) but they can't hear me.

It does however work fine on some ventrilo servers. The one server I'm using now (2.1, and only reason being is that it's the only server ventrilo actually works on without lagging all the time) always works, and I never lag...

Any help would be appreciated.

SolidSnake3035 · 04-08-2008, 08:53 PM

Okay so the problem has been pretty bad tonight so I called Optimum(my ISP) and they said that the line shows no loss, no interference, and a great connection, and that they aren't doing any packet shaping.

I'm not sure what else to do at this point...

Maybe you could help me go over my network card's advanced configuration to optimize that and see if anything there would create a problem?

Flow Control: Tx & Rx Enabled - my other option is to Disable this
Interrupt Moderation: Disabled - other option is to Enable
Jumbo Packet: 1514 Bytes - other options are 4088 and 9014
Large Send Offload (IPv4): Disabled - other option is to Enable
Max IRQ per Sec: 5000 - Able to set to any number
Priority & VLAN: Off - Able to turn On
Receive Buffers: 256 - able to set either 256 or 512
Speed & Duplex: 1000 Mbps Full Duplex - 10 half duplex, 10 full, 100 half, 100 full, auto-negotiation
TCP/UDP Checksum Offload (IPv4): Off - Able to turn On
Transmit Buffers: 256 - able to set either 256 or 512

Maybe you could take a look at these settings and see if any of them may be causing an issue, or just what could generally be optimized anyway.

Thanks.

SolidSnake3035 · 04-09-2008, 04:49 PM

Would anyone be able to help me?

SolidSnake3035 · 04-09-2008, 08:03 PM

Does anyone have any clue about those settings?

SolidSnake3035 · 04-11-2008, 02:26 PM

Bump.

This is becoming absolutely unbearable...

SolidSnake3035 · 04-13-2008, 01:03 AM

Am I completely hopeless at this point?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

04-06-2008, 08:17 PM	#11
SolidSnake3035 Junior Member Join Date: Nov 2007 Posts: 28	This seriously sucks because I have to raid tonight and I'm screwed because all I can basically do is listen since no one hears anything I say for at LEAST 5 seconds... I could be dead by the time I get a heal that I ask for, for example...

04-07-2008, 04:28 AM	#12
machz Junior Member Join Date: Apr 2008 Posts: 4	This problem started about 5 weeks ago for me as well.

04-07-2008, 08:35 PM	#13
mjgraf Senior Member Join Date: May 2005 Location: Some say in my own little world Posts: 15,502	that tracert is showing some packet loss. I Would contact the ISP and see if they are performing packet shaping, as this may be incorrectly flagging ventrilo packets as low priority.

04-07-2008, 11:31 PM	#14
SolidSnake3035 Junior Member Join Date: Nov 2007 Posts: 28	All it's showing is that one of the routes is unpingable... My ISP doesn't tell me anything, maybe YOU guys should contact them seeing as how you'd know a lot more about what to tell them than I would. Maybe they'd listen to someone from the company that actually makes the program.

04-08-2008, 09:56 AM	#15
Fayde Junior Member Join Date: Apr 2008 Posts: 10	I have the excat same problem. Although, sometimes it works fine for long perdiods of time, and sometimes the lag comes every minute. I can still hear everyone perfectly, with no delay (I usually have 10 ms depending on server) but they can't hear me. It does however work fine on some ventrilo servers. The one server I'm using now (2.1, and only reason being is that it's the only server ventrilo actually works on without lagging all the time) always works, and I never lag... Any help would be appreciated.

04-08-2008, 08:53 PM	#16
SolidSnake3035 Junior Member Join Date: Nov 2007 Posts: 28	Okay so the problem has been pretty bad tonight so I called Optimum(my ISP) and they said that the line shows no loss, no interference, and a great connection, and that they aren't doing any packet shaping. I'm not sure what else to do at this point... Maybe you could help me go over my network card's advanced configuration to optimize that and see if anything there would create a problem? Flow Control: Tx & Rx Enabled - my other option is to Disable this Interrupt Moderation: Disabled - other option is to Enable Jumbo Packet: 1514 Bytes - other options are 4088 and 9014 Large Send Offload (IPv4): Disabled - other option is to Enable Max IRQ per Sec: 5000 - Able to set to any number Priority & VLAN: Off - Able to turn On Receive Buffers: 256 - able to set either 256 or 512 Speed & Duplex: 1000 Mbps Full Duplex - 10 half duplex, 10 full, 100 half, 100 full, auto-negotiation TCP/UDP Checksum Offload (IPv4): Off - Able to turn On Transmit Buffers: 256 - able to set either 256 or 512 Maybe you could take a look at these settings and see if any of them may be causing an issue, or just what could generally be optimized anyway. Thanks.

04-09-2008, 04:49 PM	#17
SolidSnake3035 Junior Member Join Date: Nov 2007 Posts: 28	Would anyone be able to help me?

04-09-2008, 08:03 PM	#18
SolidSnake3035 Junior Member Join Date: Nov 2007 Posts: 28	Does anyone have any clue about those settings?

04-11-2008, 02:26 PM	#19
SolidSnake3035 Junior Member Join Date: Nov 2007 Posts: 28	Bump. This is becoming absolutely unbearable...

04-13-2008, 01:03 AM	#20
SolidSnake3035 Junior Member Join Date: Nov 2007 Posts: 28	Am I completely hopeless at this point?